If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
– Installation and service must be performed by a qualified installer, service agency or the gas supplier.
WARNING:
Never Operate the Top Surface Cooking Section of this Appliance Unattended
Failure to follow this warning statement could result in fire, explosion, or burn hazard that
could cause property damage, personal injury, or death.
If a fire should occur, keep away from the appliance and immediately call your fire
department.
DO NOT ATTEMPT TO EXTINGUISH AN OIL/GREASE FIRE WITH WATER.
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Tools Needed
Adjustable wrench
Tape measure
Marker or pencil
Pipe wrench
Flat-blade screwdriver
15/16" (24 mm) combination wrench
Wrench or channel lock pliers
Pipe-joint compound resistant to Propane gas
Noncorrosive leak-detection solution
For Propane/Natural Gas Conversions
Adjustable wrench
Drive ratchet
Large flat-blade screwdriver
T-20 Torx Driver
Masking tape
1/2" (1.3 cm) open end wrench
IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of
ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or
unintended operation.
In the State of Massachusetts, the following installation instructions apply:
I Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by
the State of Massachusetts.
I Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.
I A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).
† Torx and T20 are trademarks of Acument Intellectual Properties, LLC.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
Parts Supplied
Check that all parts are included.
■ Gas pressure regulator
■ Burner grates
■ Burner caps
■ Griddle drip tray (on griddle models)
■ Foam tape
Parts Needed
All models must be installed with a backsplash if installing at zero clearance to a combustible back wall. See the “Cabinet
Dimensions” section in the “Location Requirements” section for installation requirements.
To order, see the “Assistance or Service” section of the Use and Care Guide.
Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See the “Electrical Requirements”
and “Gas Supply Requirements” sections.
High Altitude Conversion
Reorificing of this range/rangetop is not required for proper operation. Low burner rates may require resetting for best
results.
Refer to the “Adjusting Simmer Low Setting on Surface Burner for Propane” section (page 14) for Propane Gas Operation.
Refer to the “Adjusting Simmer Low Setting on Surface Burner for Natural Gas” section (page 17) for Natural Gas Operation.
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances.
Do not obstruct flow of combustion and ventilation air.
■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located on the underside of the cooktop burner base.
■ It is recommended that a 585 CFM (993.9 m3/hr) or larger vent hood be installed above the cooktop.
■ Follow the range hood or microwave hood combination installation instructions for dimensional clearances above the
cooktop surface.
■ The cooktop should be installed in a location away from strong draft areas, such as windows, doors, and strong heating
vents or fans.
■ All openings in the wall or floor where cooktop is to be installed must be sealed.
■ Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.
■ Grounded electrical supply is required. See the “Electrical Requirements” section.
■ Proper gas supply connection must be available. See the “Gas Supply Requirements” section.
■ The cooktop is designed to be supported by a solid floor in accordance with the manufacturer’s instructions.
